As an Amazon Associate, we earn from qualifying purchases. This post contains affiliate links – if you buy through them, we may earn a commission at no extra cost to you.
The number that splits these five welders is the input voltage. The ARCCAPTAIN 200A Stick is the one listed for both 110V and 220V, so it follows you to a garage with a heavier circuit. On that, the YESWELDER 135A MIG leads, because it ships with flux core wire and needs no gas cylinder.
Head to Head on What Matters
Voltage and Power Source
This is the first spec to check, because it decides where you can plug in. The ARCCAPTAIN 200A Stick is the only one here listed as 110V/220V, so it can run on a household outlet or a heavier circuit. The YESWELDER 135A MIG, BILT HARD 135A 3-in-1, TOOLIOM 135A Mini and Saker Portable Welder are all listed at 110V input only. The TOOLIOM listing carries an explicit warning: connecting it to 220V will cause immediate damage and fire risk. If you only have standard household outlets, all five work.
What Comes in the Box
The BILT HARD 135A 3-in-1 is the most complete kit on paper: solar-powered helmet, 6.6ft MIG gun with a pre-installed 0.030″ tip, 10ft ground clamp, 2lb of flux core wire, a spare 0.035″ tip, and a brush and hammer. The YESWELDER 135A MIG includes extra E71T-GS.030″ and.035″ flux core wires. The ARCCAPTAIN 200A Stick includes a shoulder strap. The TOOLIOM 135A Mini includes an adjustable shoulder strap but no TIG torch, and the listing names the exact replacement to buy. The Saker Portable Welder is listed as a handheld unit, and its listing doesn’t describe a helmet, wire or clamp in the box.
Processes and Materials
Three of these run three processes. The YESWELDER 135A MIG and BILT HARD 135A 3-in-1 both do flux core MIG, Stick and Lift TIG, with a TIG torch sold separately. The ARCCAPTAIN 200A Stick does Stick and Lift TIG, and its listing names 6010, 6011, 6013 and 7018 rods. The TOOLIOM 135A Mini is a 2-in-1 Stick and Lift TIG unit for 6011 and 6013 electrodes, suited to mild steel, cast iron and stainless steel.
1. YESWELDER 135A MIG Welder
Best for: All-round home and auto body work
This is the one to pick when you want one machine for most jobs. Its synergic control matches voltage to your wire feed speed, which takes the guesswork out of setting up for thin auto body panels, and the ±3V micro-adjustment lets you fine-tune from there. At 11.4 lbs with a carry handle, it moves around a garage without much effort, and the oversized LED display stays readable outdoors. It runs flux core MIG, Stick and Lift TIG, so you need to buy a Lift TIG torch separately to use that third mode. This isn’t the welder for someone who needs to weld plate thicker than 3/32″, because the listing gives 3/32″ as the thickness it handles.
Pros
- Synergic control auto-matches voltage to wire feed speed
- Handles mild steel up to 3/32″ thick
- Includes E71T-GS.030″ and.035″ flux core wire
- Over-current, over-load and over-heating protection built in
Cons
- Lift TIG needs an extra torch, sold separately
- 110V input only, so no 220V option
2. ARCCAPTAIN 200A Stick
Best for: Buyers who may get a 220V outlet
This is the only welder here listed for both 110V and 220V, which is the whole reason to consider it. The synergic control matches current and voltage once you select the electrode diameter, and the LED screen is readable without lifting your helmet. At 7.2 lbs with a shoulder strap in the box, it’s easy to carry to a job. Its listing names 6010, 6011, 6013 and 7018 rods, so check your rod stock before buying. This isn’t the welder for someone who wants flux core MIG, because it does Stick and Lift TIG only.
Pros
- Runs on 110V and 220V input
- 7.2 lbs with a shoulder strap included
- Adjustable hot start and arc force, plus anti-stick
- 2-year quality service stated by the seller
Cons
- Stick and Lift TIG only, no MIG mode
- Lift TIG torch not included
3. BILT HARD 135A 3-in-1 IGBT Inverter Welder
Best for: First-time welders who want everything
The kit is what separates this one. You get a solar-powered helmet, a pre-installed MIG gun, a ground clamp, 2lb of flux core wire, a spare tip, and a brush and hammer, so there’s no second order before your first weld. The synergic system adjusts voltage and feed speed from the amperage you set, which suits a beginner still learning what the knobs do. It also adds 2T, 4T and Spot trigger modes for quick fixes, long seams or spot work. When it overheats or draws too much current, the display shows E1 or E2 and the fan keeps running for 1-2 minutes before a safe restart. This isn’t the welder for someone who already owns a helmet and wire, since you’d be paying for kit you have.
Pros
- Full kit including solar-powered helmet and 2lb of wire
- 2T/4T/Spot trigger modes
- Error codes E1 and E2 show on the LED display
- Lift TIG torch not included but the mode is there
Cons
- 110V input only
- TIG torch sold separately
4. TOOLIOM 135A 110V Mini Stick Welder
Best for: Simple stick work on a tight budget of space
This is a small Stick unit for people who don’t need MIG. It handles 6011 and 6013 electrodes and suits mild steel, cast iron, stainless steel and hard surfacing, with anti-stick, arc force and hot start built in. The digital display reads output current, and a trouble indicator tells you when something is off. An adjustable shoulder strap makes it easy to carry between job sites. The listing is blunt about one thing: this is 110V input only, and connecting it to 220V will cause immediate damage and fire risk, so check your outlet first. It’s not for anyone who wants to weld thin auto body panels, because Stick on thin sheet is a harder skill than flux core MIG.
Pros
- Handles 6011 and 6013 electrodes
- Anti-stick, arc force and hot start built in
- Adjustable shoulder strap for carrying
- Digital display shows output current
Cons
- 110V input only, with a stated 220V damage and fire risk
- Lift TIG torch not included
5. Saker Portable Electric Welding Machine
Best for: One-handed work in tight spots
At 3.3 lbs and 9.8″ x 9.45″, this unit is built to be carried, and the handheld design lets you work one-handed where a bench machine won’t reach. Output is adjustable from 20 to 120 amps through a 5-speed knob, and it takes 3/32″ rods. Hot start arc ignition helps the rod strike cleanly, and the listing says the current adjustment reduces spatter on carbon steel and iron. A 360° cooling design with built-in overheat protection is meant to keep it running through longer sessions.
Pros
- 3.3 lbs, handheld for one-handed use
- Adjustable 20-120 amp output on a 5-speed knob
- Hot start arc ignition for easier starts
- Built-in overheat protection with 360° cooling
Cons
- Stick process only
- 110V input only
Also Worth Considering
The SEESII MIG Welder is a 135A 110V multi-process unit running gasless flux core, Lift TIG and Stick, with a large digital display and a listed weight of 7.7 lbs. If you want a light multi-process machine, it’s worth a look.
The FEMEROL MIG Welder is a 140A multi-process machine for flux core, MIG, Lift TIG and Stick on 110V, with synergic control, an LED display and welding helmets included. The 140A figure is the highest among the 110V multi-process units here.
The ARCCAPTAIN Core MIG Welder is a 135A 110V machine covering gasless flux core MIG, Stick and Lift TIG. It’s the same brand as the dual-voltage stick unit above, in a multi-process format.
Frequently Asked Questions
Is a higher amp rating always better?
No. On 110V, the YESWELDER 135A MIG is listed as handling mild steel up to 3/32″, so extra amps only matter on thicker metal. Match the rating to the metal you actually weld.
What does an unlisted spec mean?
It means the seller didn’t state it, not that the feature is missing. If a listing doesn’t mention a helmet or a torch, treat it as unknown and ask the seller before you buy.
How do I compare a 135A machine with a 200A one?
Check the input voltage first. A 200A rating on 110V and 220V isn’t the same as 200A on 110V alone, so compare the volts and the thickness each listing says it handles.
Can I use a 110V welder on a household outlet?
Yes, all five here are listed for standard 110V household voltage. The TOOLIOM listing warns that connecting it to 220V will cause immediate damage and fire risk, so always check your outlet before plugging in.
Conclusion
The YESWELDER 135A MIG wins on the axis that matters most for home work: it welds thin steel with synergic control and includes the wire. If you’re not sure which axis you care about, the BILT HARD 135A multi-process machine is the safer pick, because the helmet and wire come with it. Check your outlet, then pick your machine.
Hi, I’m Zachary Ford. I’m passionate about welding and dedicated to helping both beginners and experienced welders make informed decisions. I research, test, and write about welding helmets, welding machines, safety equipment, and essential workshop tools. My goal is to provide honest reviews, practical buying guides, and easy-to-follow tutorials that help you weld more safely, work more efficiently, and choose the right gear with confidence.